Zodiac TRI CHLORINE GENERATOR User Manual Page 4

  • Download
  • Add to my manuals
  • Print
  • Page
    / 20
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 3
Recommendations
Important information
YOU MUST READ THE FOLLOWING INFORMATION BEFORE PROCEEDING
WITH THE INSTALLATION. ALWAYS READ THE USER MANUAL BEFORE USING
THE DEVICE. WE RECOMMEND THAT YOU KEEP THE USER MANUAL IN A
SAFE PLACE.
Zodiac believes in safety fi rst
At Zodiac, we take safety seriously. Always exercise caution when using
electrical appliances and follow the instructions. Failure to do so could result
in permanent injury, electrocution or drowning.
Warnings
Zodiac water treatment products are designed for domestic swimming pool
use only. Inappropriate use could affect performance and void the warranty.
Operating a saltwater chlorinator associated with pH regulator without any
water fl owing through the cell may cause a build-up of fl ammable gases, which
could result in fi re or explosion.
Keep the equipment out of the reach of children.
A damaged supply cord should only be replaced by the manufacturer,
authorized service agent or electrician.
When installing and using this electrical equipment, always follow basic safety
precautions.
Before performing installation, disconnect all power.
Connect to a circuit that is protected by a ground fault circuit interrupter
(GFCI).
Service to Zodiac equipment should only be carried out by qualifi ed and
authorized pool professionals.
Child Safety
Children should not be allowed to operate or perform maintenance on this
product.
No one, particularly children, should sit, step, lean, or climb on any of your
pool’s operational system.
In the interest of child safety, all components of a pool’s operational system
should be located at least 3 meters away from the pool.
Electrical Hazard
The Zodiac TRi Power pack on which the TRi PRO module is connected must
not come into contact with water and should be installed at least 3 meters
from the inside wall of your swimming pool.
When a lack of water is detected, the unit’s electronic fl ow switch is designed
to turn off the system. Interfering with the electronic fl ow switch could result
in personal injury and/or damage to the cell.
2
24
(2)
(3)
(1)
Quick install guide
The following steps will help you set up and operate your new Zodiac TRi PRO
module associated with your Zodiac TRi salt water chlorinator.
IMPORTANT!
Your appliance must be installed by a qualifi ed and experienced pool
professional.
3.1/ Prepare the swimming pool
IMPORTANT:
the TRi PRO module is designed to automatically ‘MAINTAIN’ the chlorine
level (ACL) and pH in your pool.
However, it is mandatory to control and adjust water balance parameters
before installing this unit. This will help you keeping a correct water balance
during the season.
Remark: See chapter 7 / Water balance’ to know how to adjust water
parameters before installing TRi PRO module.
3.2/ Installing TRi PRO module
1. Switch off the Zodiac TRi salt water chlorinator by pressing the
button.
2. Switch off the ltration system by cutting off mains supply into
ltration’s electric enclosure.
3. Close the valves cutting off the pipework.
4. Remove the silver cover cap (1).
5. Remove screws holding the original lower module (empty) on the main
TRi unit. (2 screws on sides and 2 screws on the bottom) (2).
6. Remove the empty original module and replace it with your new TRi PRO
module. Connect the TRi PRO module ribbon cable (fl at cable with black
male connector) to the corresponding black female connector of the TRi
power pack (3).
7. Position the TRi PRO module correctly and tighten the 4 screws. Put the
silver cover cap back into place.
IMPORTANT: Do not connect the unit to mains supply before the TRi
PRO module, the POD holding sensors and its pH minus injector pipe are
installed (see chapter 3.8 / ‘Testing / Priming the peristaltic pump’).
3
!
!
!
25
Page view 3
1 2 3 4 5 6 7 8 9 ... 19 20

Comments to this Manuals

No comments