Zodiac Jandy EE-Ti Specifications

H0569300-Installation and Operation ManualInstallation and Operation DataDANGERRISK OF ELECTRICAL SHOCK OR ELECTROCUTION. The electrical supply to th

Page 8Page 9and following diagrams can affect the operation of the heat pump’s water pressure switch. Location of the heat pump above or below the poo

Page 8Page 9Figure 6. Two Heat Pump Plumbing Layout             

Page 10Page 11Figure 8. Six Heat Pump Plumbing Layout            

Page 10Page 114.1 General InformationWiring connections must be made exactly as shown in the wiring diagram found on the inside of the heat pump acce

Page 12Page 131. Be sure the power to the circuit for the heat pump is turned off2. Remove the 5 screws that attach the service/access panel

Page 12Page 13-HEATFigure 10. AE-Ti Single-Phase Electrical Supply Wiring Diagram

Page 14Page 15-HEATFigure 11. AE-Ti 3-Phase Electrical Supply Wiring Diagram

Page 14Page 15ATTENTIONAfter starting the AE-Ti heat pump, please note that there is a 5 minute delay before the compressor begins operation. The heat

Page 16Page 175.2.1 Off/On ButtonWhen the control panel is turned off, the screen displays CONTROL IS OFF and the Off/On LED indicator is not lit. Pr

Page 16Page 17the control will operate in the mode it was in when the keypad lockout occurred. If any button is pressed when the keypad is in lockout

Page 1

Page 18Page 193. Repeatedly press and release the SPA button until the display momentarily reads SETTING 05. The control panel will then display

Page 18Page 19(1.83 m) below the pool surface. Consult your local Jandy representative for recommendations.On some installations, the piping from the

Page 20Page 216.3 Spring Start-UpIf your heat pump has been winterized, perform the following steps when starting the system in the Spring: 1. U

Page 20Page 213. Do not use this heat pump if any part has been under water. Immediately call a qualied professional technician to inspect the

Page 22Page 23The hot gas enters the heat exchanger where the water extracts the heat. The pump pulls in cool pool water, which in turn converts the h

Page 22Page 23SYMPTOM CORRECTIVE ACTIONHeat pump will not start, no control board display. Breaker or fuse may be tripped. Reset breaker or check fuse

Page 24Page 25Diagnostic Condition DescriptionLOW H2O FLOW Low or restricted water flow through the heat pump. The external bypass valve is in the wr

Page 24Page 25Diagnostic Condition DescriptionLOW WATER TEMPERATURE When the POOL or SPA temperature chills to 50°F or below there could be safety ris

Page 26Page 27Key No. DescriptionModelNo.OrderPart No.1 Top Enclosure, Jacket All R30002002 Front Panel, Jacket 2000 R30004012 Front Panel, Jacket 250

Page 26Page 279.3 Jandy AE-Ti Heat Pumps Exploded View

Page 1Section 1. General Information ...21.1 Introduction... 21.2 Consumer Informatio

Page 28Page 29This page intentionally left blank.

Page 28Page 29This page intentionally left blank.

               

Page 2Page 3Section 1. General Information1.1 IntroductionThis manual provides installation and operation instructions for the Jandy AE-Ti

Page 2Page 35. Persons with a medical history of heart disease, diabetes, circulatory or blood pressure problems should consult their physician b

Page 4Page 5the absence of local codes, refer to the latest edition of the National Electric Code (NEC) in the United States and the Canadian Electric

Page 4Page 5                  Figure 1. Jandy

Page 6Page 7Ce chauffe-piscine doit être installé á au moins 5 pieds (1.52m) de la paroi interne de la piscine à moins d’être isolé de la piscine par

Page 6Page 7Note: Bolts and bolt anchors are not included with the heat pump. The installer must provide 1/4” x 1-3/8” stainless steel anchor bolts